Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube

These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.

 This part is available by special order, request a quote

The BoosterPlug is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Guzzi's.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The BoosterPlug features a unique technology to provide your bike with a controlled fuel enrichment in all ambient temperature situations. No other Plug and Play device does this. A richer mixture is provided only when needed i.e at low RPMs and when accelerating. On open roads at a constant speed the Boosterplug sits idle to keep fuel consumption low.
Make your bike run as it should have done from the factory!

• Improved and gentler throttle action when opening and closing throttle
• Richer mixture when opening the throttle improves acceleration
• Booster plug removes the uneven low speed running that is typical for modern lean burn engines
• Stronger and more consistent at idle.
• Reduced backfiring with aftermarket exhausts on engine braking
• Lifetime warranty

 1 in stock

Replacement blue LED in chrome bezel for Gutsibits clock surrounds ACA01001 and ACA01002

These 12v LEDs include a resistor, wires should be soldered to the mini spade connectors on the base of the LED

 More than 5 in stock

Black and red 60mm round Moto Guzzi badge for Hepco and Becker panniers

Guzzi pannier badge.

 More than 5 in stock

Pair of black alloy bar end extensions to enable fitment of Clubman mirrors to V7 and V9 models with threaded handlebar ends without needing to move switchgear inboard. Mirrors can be fitted without these but the handlebars need drilling for the switchgear locating pegs

 1 in stock

Lightweight M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins). An aluminium filler plug made in Italy.

 1 in stock

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00

Gorgeous polished aluminium reservoir cap for PS15 Brembo master cylinder fitted to rear linked system on many models, will fit front master cylinder on models where a PS15 handlebar master cylinder is fitted. Seal is not included with this cap - you should re-use your original cap seal

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 14661100 GU14661100 14 66 11 00
 1466 1100 1466.1100 14.66.11.00

Also fits Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR

Gorgeous polished aluminium reservoir cap for PS12 Brembo master cylinder fitted to front brake on many models, fits rear master cylinder on more recent models

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 10430830 GU10430830 10 43 08 30
 1043 0830 1043.0830 10.43.08.30

Pair of beautiful polished aluminium rocker cover protectors.

Part of the exciting range of MAS aluminium parts to make your V7 stand out from the crowd. Replaces head cover 32023410

 Sorry, this part is no longer available.